соплей нет на 128, скорость в терминале 115200
вот как прошиваю 128 может я там чтото не то делаю ? сейчас вообще не запускается
D:\1>avrdude -P COM1 -b 19200 -c avrisp -p m128 -v -v -e -U flash:w:zxevo_bl.hex
avrdude: Version 6.1, compiled on Mar 13 2014 at 00:09:49
Copyright (c) 2000-2005 Brian Dean,
http://www.bdmicro.com/ Copyright (c) 2007-2014 Joerg Wunsch
System wide configuration file is "D:\1\avrdude.conf"
Using Port : COM1
Using Programmer : avrisp
Overriding Baud Rate : 19200
AVR Part : ATmega128
Chip Erase delay : 9000 us
PAGEL : PD7
BS2 : PA0
RESET disposition : dedicated
RETRY pulse : SCK
serial program mode : yes
parallel program mode : yes
Timeout : 200
StabDelay : 100
CmdexeDelay : 25
SyncLoops : 32
ByteDelay : 0
PollIndex : 3
PollValue : 0x53
Memory Detail :
Block Poll Page Polled
Memory Type Mode Delay Size Indx Paged Size Size #Pages MinW MaxW ReadBack
----------- ---- ----- ----- ---- ------ ------ ---- ------ ----- ----- ---------
eeprom 4 12 64 0 no 4096 8 0 9000 9000 0xff 0xff
flash 33 6 128 0 yes 131072 256 512 4500 4500 0xff 0xff
lfuse 0 0 0 0 no 1 0 0 9000 9000 0x00 0x00
hfuse 0 0 0 0 no 1 0 0 9000 9000 0x00 0x00
efuse 0 0 0 0 no 1 0 0 9000 9000 0x00 0x00
lock 0 0 0 0 no 1 0 0 9000 9000 0x00 0x00
calibration 0 0 0 0 no 4 0 0 0 0 0x00 0x00
signature 0 0 0 0 no 3 0 0 0 0 0x00 0x00
Programmer Type : STK500
Description : Atmel AVR ISP
Hardware Version: 2
Firmware Version: 1.18
Topcard : Unknown
Vtarget : 0.0 V
Varef : 0.0 V
Oscillator : Off
SCK period : 0.1 us
avrdude: AVR device initialized and ready to accept instructions
Reading | ################################################## | 100% 0.08s
avrdude: Device signature = 0x1e9702
avrdude: safemode: lfuse reads as 3F
avrdude: safemode: hfuse reads as 88
avrdude: safemode: efuse reads as FF
avrdude: erasing chip
avrdude: reading input file "zxevo_bl.hex"
avrdude: input file zxevo_bl.hex auto detected as Intel Hex
avrdude: writing flash (131072 bytes):
Writing | ################################################## | 100% 135.26s
avrdude: 131072 bytes of flash written
avrdude: verifying flash memory against zxevo_bl.hex:
avrdude: load data flash data from input file zxevo_bl.hex:
avrdude: input file zxevo_bl.hex auto detected as Intel Hex
avrdude: input file zxevo_bl.hex contains 131072 bytes
avrdude: reading on-chip flash data:
Reading | ################################################## | 100% 88.28s
avrdude: verifying ...
avrdude: 131072 bytes of flash verified
avrdude: safemode: lfuse reads as 3F
avrdude: safemode: hfuse reads as 88
avrdude: safemode: efuse reads as FF
avrdude: safemode: Fuses OK (E:FF, H:88, L:3F)
avrdude done. Thank you.
D:\1>